Although there are many types of rolling shutter doors in Jinan, such as wind resistant rolling shutter doors, the sales volume of electric rolling shutter doors is much higher than that of manual rolling shutter doors. Many people are interested in the installation of Jinan electric rolling shutter door. Today, the rolling shutter door manufacturer will introduce the installation tutorial of electric rolling shutter door for you in detail.

濟南卷簾門

Jinan roller shutter door

一、安裝大小鐵板

1、 Installation of large and small iron plates

電動卷簾門大小鐵板的安裝又分為垂直安裝和水平安裝兩種，其中垂直安裝主要用于大鐵板的下口，門洞口向上5cm來確定安裝位置。水平安裝則是以圓管長度減去門洞長度加2cm除以2，兩邊平分來確定大小鐵板之間位置安裝。小鐵板以大鐵板的點水平來確認小鐵板的水平點安裝位置。

The installation of large and small iron plates of electric rolling shutter door is divided into vertical installation and horizontal installation. Vertical installation is mainly used for the lower opening of large iron plate, and the installation position is determined by 5cm upward of door opening. For horizontal installation, the length of the round pipe minus the length of the door opening plus 2cm divided by 2, and the two sides are equally divided to determine the position between the large and small iron plates. The installation position of the small iron plate is confirmed by the level of the center point of the large iron plate.

二、安裝圓管

2、 Install round pipe

將圓管有缺口一側套在大鐵板的鏈盤上，再將軸承座套在圓管軸頭上，用螺絲將軸承座緊固在小鐵板上。

Put the notched side of the round pipe on the chain plate of the large iron plate, and then put the bearing seat on the shaft head of the round pipe, and fasten the bearing seat on the small iron plate with screws.

三、安裝電機

3、 Install the motor

電動卷簾門的電機在安裝一定要牢固，鏈條松緊應適當。電機上的所有接線頭需用電工膠帶纏緊，禁止將多余電源線纏繞在電機上，以防止電機發(fā)熱造成的電源線漏電、短路等隱患。

The motor of the electric rolling shutter door must be firmly installed, and the chain tightness should be appropriate. All terminals on the motor shall be wrapped tightly with electrical tape. It is forbidden to wind the redundant power line on the motor to prevent the power line leakage, short circuit and other potential safety hazards caused by motor heating.

四、安裝門體

4、 Install the door body

將電動卷簾門的吊沿片、底梁串到門片上，門片通過電機上升適當位置，再將吊沿片緊固在圓管上，進行上下調整，保持上下對齊，加緊門片，防止竄體卡口。

The hanging edge piece and bottom beam of the electric rolling shutter door are connected to the door piece. The door piece is lifted to the appropriate position through the motor, and then the hanging edge plate is fixed on the round pipe for up and down adjustment to keep the alignment between the upper and lower parts, and tighten the door piece to prevent the channeling bayonet.

五、安裝導軌

5、 Install the guide rail

將事先依照尺寸、要求制作好的抗風門導軌立于門洞兩側，注意上下兩頭需保持水平。再用螺栓固定好軌道，結束之后蓋好工業(yè)門導軌封蓋。

Put the anti wind door guide rail made according to the size and requirements in advance on both sides of the door opening, and pay attention to keep the upper and lower ends horizontal. Then fix the track with bolts, and cover the guide rail cover of industrial door after finishing.

六、調試限位

6、 Commissioning limit

電動卷簾門的限位在電機里，打開電機外殼，調整門體的上、下限位，要求上限位距離門洞少要有一個底梁位置，下限位與地面要保持密封。多次反復試驗幾次，直到上下開門達到理想位置即可停止。

The limit of the electric rolling shutter door is in the motor. Open the motor shell and adjust the upper and lower limits of the door body. It is required that there should be at least one sill position between the upper limit and the door opening, and the lower limit should be sealed with the ground. Repeat the test several times until the upper and lower doors reach the ideal position.

上述內容便是濟南電動卷簾門的安裝教程，大家可以好好了解一下，對于大家安裝電動卷簾門是很有幫助的。

The above content is Jinan electric rolling shutter door installation tutorial, you can have a good understanding, for you to install electric rolling shutter door is very helpful.